Service Hotline: 13823761625

Products

Contact Us

You are here:Home >> Products >> MCU >> MCU

MCU

NY8A051B

  Ny8a051b is an 8-bit OTP MCU. The core of ny8a051b is based on RISC reduced instruction set architecture, with a total of 55 instructions.
  In terms of I / O resources, ny8a051b has 6 elastic bidirectional I / O pins, and each I / O pin has a separate register to control as input or output pin.
  Ny8a051b has two sets of timers,. In addition, ny8a051b provides 1 set of PWM outputs. Ny8a051b adopts dual clock mechanism. Under the dual clock mechanism, ny8a051b can select a variety of working modes, such as normal mode, slow mode, standby mode and half mode. In power-saving modes, such as standby mode and sleep mode, there are a variety of events that can trigger interrupt wake-up ny8a051b to enter normal mode or slow mode to deal with emergencies.
    NY8A051B General Description:  
      NY8A051B is an EPROM based 8-bit MCU tailored for I/O based applications like home appliances or meter equipment. NY8A051B adopts advanced CMOS technology to provide customers remarkable solution with low cost, high performance and high noise immunity benefits. RISC architecture is applied to NY8A051B and it provides 55 instructions. All instructions are executed in single instruction cycle except program branch and skip instructions which will take two instruction cycles. Therefore, NY8A051B is very suitable for those applications that are sophisticated but compact program size is required.
      As NY8A051B address I/O type applications, it can provide 6 I/O pins for applications which require abundant input and output functionality. Moreover, each I/O pin may have additional features, like Pull-High/Pull-Low resistor and open-drain output type through programming. Moreover, NY8A051B has built-in infrared (IR) carrier generator with selectable IR carrier frequency and polarity for applications which demand remote control feature.
      NY8A051B also provides 2 sets of timers which can be used as regular timer based on system oscillation or event counter with external trigger clock. Moreover, NY8A051B provides 1 set of 8-bit resolution Pulse Width Modulation (PWM) output and buzzer output in order to drive motor/LED and buzzer.
      NY8A051B employs dual-clock oscillation mechanism, both high oscillation or low oscillation can be derived from internal resistor/capacitor oscillator. Moreover, based on dual-clock mechanism, NY8A051B provides kinds of operation mode like Normal mode, Slow mode, Standby mode and Halt mode in order to save power consumption and lengthen battery operation life.
      While NY8A051B operates in Standby mode and Halt mode, kinds of event will issue interrupt requests and can wake-up NY8A051B to enter Normal mode and Slow mode in order to process urgent events.
    NY8A051B Features:
    Wide operating voltage range: (@ 4 CPU clock per instruction, i.e. 4T mode) 
    2.0V ~ 5.5V @system clock ≦8MHz.
    2.2V ~ 5.5V @system clock >8MHz.
    Wide operating temperature: -40°C ~ 85°C.
    High ESD over ±8KV.
    High EFT over ±4KV with Noise Filter Enable. (Operating voltage @5V)
    1K x 14 bits EPROM.
    48 bytes SRAM.
    6 general purpose I/O pins (GPIO), PB[5:0], with independent direction control. ? 
    PB[3:0] have features of Pull-Low resistor for input pin.
    PB[5:4] and PB[2:0] have features of Pull-High resistor, and open-drain output. ? 
    PB[3] have feature of input or open-drain output.
    8-level hardware Stack.
    Direct and indirect addressing modes for data access.
    One 8-bit up-count timer (Timer0) with programmable prescaler.
    One 8-bit reload or continuous down-count timers (Timer1).
    One 8-bit resolution PWM (PWM1) output.
    One buzzer (BZ1) output.
    Selectable 38/57KHz IR carrier frequency and high/low polarity according to data value.
    Built-in Power-On Reset (POR).
    Built-in Low-Voltage Reset (LVR).
    Built-in Watch-Dog Timer (WDT) enabled/disabled by firmware control.
    Dual-clock oscillation: System clock can switch between high oscillation and low oscillation.
    High oscillation: I_HRC (Internal High Resistor/Capacitor Oscillator ranging from 1M~20MHz) ? Low oscillation:  I_LRC (Internal 32KHz oscillator)
    Four kinds of operation mode to reduce system power consumption: 
    Normal mode, Slow mode, Standby mode and Halt mode.
    Five hardware interrupt events: 
    Timer0 overflow interrupt.
    Timer1 underflow interrupt.
    WDT timeout interrupt.
    PB input change interrupt.
    External interrupt.
    Five interrupt events to wake-up NY8A051B from Standby mode: 
    Timer0 overflow interrupt.
    Timer1 underflow interrupt.
    WDT timeout interrupt.
    PB input change interrupt.
    External interrupt.
    Three interrupt events to wake-up NY8A051B from Halt mode: 
    WDT timeout interrupt.
    PB input change interrupt.
    External interrupt.
    NY8A051B Ordering Information:

    P/N

    Package Type

    Pin Count

    Package Width

    Shipping

    NY8A051B

    Die

    --

    --

    --

    NY8A051BS6

    SOT23-6

    6

    63 mil

    Tape & Reel: 3.0K pcs per Reel

    NY8A051BS8

    SOP

    8

    150 mil

    Tape & Reel: 2.5K pcs per Reel Tube: 100 pcs per Tube

    NY8A051BP8

    PDIP

    8

    300 mil

    Tube: 50 pcs per Tube

    NY8A051B Block Diagram:

    NY8A051B Pin Assignment:




    NY8A051B provides three kinds of package type which are SOP8, DIP8 and SOT23-6:



    Please submit your basic information and send an email Sales@ChipSourceTek.com , or call us at 13823761625 (the same number as wechat), and we will contact you as soon as possible!

    *

    *

    *

    *

Related products