Service Hotline: 13823761625

Support

Contact Us

You are here:Home >> Support >> Technology

Technology

Principle and design of high fidelity BTL amplifier

Time:2022-07-10 Views:2028
    This paper introduces a BTL Power amplifier circuit without debugging, with high fidelity and low cost, and the final power amplifier IC can be selected according to your own situation. Because of its strong versatility, it brings great convenience to audio lovers.

    Working principle high fidelity BTL amplifier (tda2009)



    Only the circuit diagram of one channel is given here, and the other channel is exactly the same. The audio signal is input from the a end of the circuit, amplified by the operational amplifier IC1 (the amplification factor is determined by R1 and R2), and then inverted amplified by IC2, with a gain of 1; The other way is amplified twice through IC3 and iC4, and the gain is still 1. The essence is that IC3 and iC4 together form a positive phase amplifier with a gain of 1. Therefore, two equal and opposite phase audio signals are obtained at the B end of IC2 and the C end of iC4. These two mutually inverted audio signals are respectively added to the ① and ⑤ pins of the dual audio power amplification integrated circuit IC5 (tda2009) through R9, C5, R10 and C6. These two inputs are in-phase input and inverted input. Therefore, after power amplification in IC5, they are output from the ⑩ and ⑧ pins of IC5 respectively to drive the speaker BL.

    Component selection and debugging

    See the following table for the list of components.

    The circuit working principle of the device is shown in Figure 1

No

Name

Model

Quantity

No

Name

Model

Quantity

R1

resistance

1K

1

C11

Electrolytic capacitor

47u

1

R22021

resistance

10K

3

C1213

Polyester capacitor

0.1u

2

R3R9R12

resistance

220K

3

C14

Electrolytic capacitor

10u

1

R4R710111316

resistance

20K

8

C15

Ceramic chip capacitor

0.01u

1

R81415

resistance

100Ω

3

C16

Electrolytic capacitor

100u

1

R1718

="9%"> resistance

10Ω

2

DW

Zener diode

20V

1

R19

resistance

2.7K

1

VT

Crystal triode

2N5551

1

C13456

Electrolytic capacitor

1u

5

IC1

Quad op amp IC

TL084

1

C2

Electrolytic capacitor

4.7u

1

IC2

Dual channel power amplifier IC

TDA2009

1

C78

Ceramic chip capacitor

1000P

2

BL

speaker

48Ω

1

C910

Electrolytic capacitor

220u

2

 

 

 

 

    Ic1-ic4 can use a four op amp integrated circuit tl084. The differential amplifier has wide frequency response, low noise and high transient index. In addition to tda2009, the power integrated amplifier can also use other similar integrated circuits without special requirements. All the resistors used are low-noise, precision metal film resistors, which are designed to reduce the noise of the pre stage. At the same time, the signal amplitude of B and C should be equal. The pre stage coupling capacitor used should also be precision tantalum capacitor. The power of triode VT should depend on the current required by the circuit, and there should be enough capacity reserve to obtain good transient characteristics and sufficient dynamic range.

    Due to the versatility of this circuit design, any dual power amplifier IC with OTL or OCL output can be connected with the B and C ends of the differential amplifier to form a BTL amplifier. If readers are interested, they can also insert RC attenuation tone control circuit, which will get better results.


    Disclaimer: This article is transferred from other platforms and does not represent the views and positions of this site. If there is infringement or objection, please contact us to delete. thank you!
    矽源特科技ChipSourceTek